2004 Dodge Ram 1500 Ball Joint Torque Specs

Remove tire Pull codder pin and remve nut Tap ball joint out of. Moog problem solver front upper ball joint for the 00-02 Dodge Ram 150025003500 trucks.

Mini R50 R53 Torque Wrench Settings Mini Cooper Mini 2006 Mini Cooper

And if so are there torque specs on the new ball joints.

2004 dodge ram 1500 ball joint torque specs. Do not check for axial movement. But what do I torque the ball joint mounting bolts to. Axle identification-Model 60 front axle differential cover.

Torque the 22mm lower ball join nut to 38 foot-pounds and add an additional 90. Ive got blue loctite so will use that. Tighten the mounting bolts to 42 ft.

DODGE RAM 2006 STEERING KNUCKLE BALL JOINT TORQUE SPECS - YouTube. Chassis Torque Specs 4th Gen RAM Shock Absorber Upper Nut -----40 ft lbs Shock Absorber Lower Bolt -----100 ft lbs Shock Tower to Frame -----55 ft lbs. The FSM says the upper ball joint to knuckle is 60 ft-lbs.

Torque the upper ball joint to 40 ft-lbs and the lower to 100 ft-lbs. Torque Specifications for Dodge Ram Pickup. Im guessing LD1500 and HD25003500.

Thanks in advance for any assistance. Truck 2008 dodge ram 2500 diesel 4x4 upper and lower ball joint torque specs Big A there are specs for the ball joint stud nuts Dodge Dakota Ball Joint Torque Specs pdfsdocuments2 com April 12th 2019 - This document is meant to help in the replacement of the upper ball joint of a 1999 Durango 4x4 Using two ½ sockets bolt the new ball joint. The Moog-K7366 is a great way to upgrade your OE suspension.

Dodge ram 1500 4x4. Torque the castellated nut to 108 ft. Im not sure how youre supposed to get a torque wrench on the upper ball joint so I just tightened it down and called it.

Makes it a lot easier to air hammer. Typical ball joint removal using the special tools-248 FBI axle shown. But cant find any torque values for the 3 upper and 4 lower mounting bolts.

I need torque specs for a 2004 Dodge Ram 1500 SLT 4x4 57l on upper ball joints lower ball joints outer tiered end and caliper mounting bracket. I highly recommend that you have a press available they dont screw in unfortunatly015012015012015012015012To change uper ball joints. Front Wheel Hub Torque Specifications Spécifications de couple pour moyeu de roue avant Always refer to the specific vehicle manufacturers instruction manual for installation procedures.

Install is reverse but dont tighten the 4 lower ball joint set bolts. My vehicle is a 1998 Dodge Ram 1500 4WD w 52LV8. Nm Front Drive Shaft-To-Front Axle Flange Bolt 14 19 Front Drive Shaft Flange-To-Transfer Case Flange Bolt 65 88 Rear Drive Shaft Center Bearing-To-Crossmember Bolt 50 68 Rear Drive Shaft Universal Joint Strap-To-Rear Axle Flange Bolt Dana Axle 22 30 9 14 Axle 14 19.

Access our Ram 1500 2500 3500 2001-2005 Upper Ball Joints Repair Guide Removal and Installation by creating an account or signing into your. Torque the 22mm upper ball join nut to 40 foot-pounds and add an additional 90 degrees. Tighten the 22mm upper ball joint nut.

Axle identification-Model 44 front axle differential cover. APPLICATIONS BALL JOINT BALL JOINT MODEL FRONT LOWER ARM FRONT LOWER ARM 9-30 IN-LBS TEST D REAR LOWER ARM 1 Do not check for radial movement. Torque is as follows.

TORQUE SPECIFICATIONS RAM PICKUP Application Ft. ADV710 revised 0498 Page 3. Ball joint to control arm- 112 ft-lbs Tie rod nut- 67 ft-lbs lower ball joint set bolts- 83 ft-lbs remember to use a new cotter pin.

Upper ball joint specs. Rough Country 4 Lift 125 RCX Body Lift Bilstein 5100s Set to 07 Bilstein 5125 Rear Shocks Fuel Throttle Wheels 20x9 1mm Toyo MT 3512520s Tri-Fold Tonneau Cover 5 Side Tint 2 Rear Tint PlasmaGlow Firestorm LED Tailgate Bar Painted Grille 5K HID Heads and Fogs LED Interior Lights Tow Hooks 3500 Ram Flares Blendmount Radar Mount 20 Rigid LED Bully. Anti RollStabilizer Bar To Axle Assembly.

And the lower ball joint to knuckle is 95 ft-lbs for LD and 110 ft-lbs for HD. Lower ball joint specs. Torque the ball joint-to-control arm nutsbolts to 85 ft.

Torque specslower shock boltssteering I NEED THE TORQUE SPECS FOR THE LOWER A-ARM BOLTS UPPER AND LOWER SHOCK BOLTS OUTER TIE RODS AND STEERING STABILIZER END LINKS FOR AN 09 DODGE RAM 1500 4X4. Slide the upper ball joint into the spindle. You are correct to drill a hole in the OEM rivets to remove the rivets.

I was just curious as to how much labor is involved. MOOG moog-k7366. 57 Nm and the castellated nut to 72 ft.

2008 Dodge Ram 3500 Values Cars For Sale Kelley Blue Book